How Much Does it Cost to Install a Gas Line Shut Off Valve?

$350 – $550

It will generally cost between $350-$550 to hire a plumber to install a gas line shut-off valve in an existing line.  The job involves cutting the gas line and installing the valve. Depending on the setup, it might also involve reattaching a length of pipe and a fitting for whatever gas appliance or equipment is being used at the location.

Gas Line Advice and Installation Quotes from Plumbers Near You

Gas Line Advice and Installation Quotes from Plumbers Near You


Average Cost of Gas Shutoff Valve Installation

Each appliance that is run on natural gas or propane must have a shut-off valve.  There should also be a main shut-off valve at the gas meter or where the gas line enters the home.

The cost to purchase the gas-main or street-view gas shut-off valve will run between $100-$300 for just the valve.  The price is determined by the size of the gas pipe used and the pressure capabilities that the valve can handle. Valves for shutting off gas to an appliance are much more affordable, though installation labor rate is about the same.

Labor to install a gas shut-off valve is usually an additional $150-$200, plus there are extra costs associated with miscellaneous supplies.

Average Do It Yourself cost
$50 – $200
Average Contractor Installed Cost
$350 – $550
Typical Cost Average
$425 – $500
Last Updated: Thursday, September 30, 2021

gas line shut off valve installed on furnace
Image Courtesy of Fuse Appliance Repair

Overview of Gas Valve Installation

Gas shut off valves, also known as supply valves, are located either at the exterior of the house or just inside the home.  There should also be shut-off valves near every appliance that uses gas or propane such as a gas range, gas fire pit or gas logs in a fireplace. Just to clarify, gas shut-off valves can also be known as gas shut off or gas shutoff valves. The term gas turn off valve is also used. The  terms are interchangeable.

The gas shut-off valve just outside of the home near the natural gas meter is called the main valve and should have been installed by the gas company at the time the home was built or when the equipment was updated over the years.

This page of Costimates includes cost factors, price estimates from around the internet and a DIY or Not suggestion. We include reader-submitted prices too, so please consider bookmarking this page to return and share your project cost for the benefit of other readers.

Note: Areas that are prone to earthquakes, such as California, often require a special type of gas shut-off valve called excess flow valves or EFV.  These valves are much more expensive than the typical main or appliance shut-off valves.  The price to install the excess flow valves, aka seismic gas valves, can be $500 to $1,000 or more, depending on site conditions and the ease to access the main gas line.

Gas Line Advice and Installation Quotes from Plumbers Near You

Gas Line Advice and Installation Quotes from Plumbers Near You

Product and Installation Supplies Cost Details

Gas Line Installation Cost Factors

There are a few essential factors that will affect the cost to install or replace a gas shut-off valve. While we mention the DIY option, this is one of the indoor home improvement projects best left to a plumber or mechanical contractor.

  • Valve Type – This is the major factor. Main gas shut-off valves are more expensive than gas appliance shut-off valves.  Retail costs are found below. As noted, if the shut-off valve is installed in an earthquake-prone area that requires an excess flow valve or EFV, then the price will be much higher.
  • Who Installs the Valve – Installing an appliance shut off valve for a newly run gas line can be DIY if you really know what you’re doing or done by a handyman. Main valve or street side valve installation or replacement should be done by a licensed plumbing contractor.
  • Access to the Location – The ease to which a licensed plumber or a certified heating/cooling technician can access the area where the shut-off valves need to be installed factors into the cost estimate. A valve on a line running to a stand-alone fireplace in a living room, for example, will be easier to install than on in serving a water heater in a crawlspace. Appliance shut-off valves generally will take less than an hour to install, so the price can run from $75-150 for the installation labor.  Main gas shut-off valves can take two to three hours, depending on work conditions.
  • How Many Valves are Being Installed – Cost per valve drops a little when two or more valves are installed. This is because the plumber is already on site with tools and the equipment needed for the work.
  • Cost of Living – The general cost of living in your area will affect labor rates. Costs are highest on the Coasts, especially the Northeast and Northwest. Rates are lower in the middle of the country, especially in rural areas and smaller towns.
  • Whether Appliance Installation is Included – The costs listed here do not include the cost to install a gas appliance or to run a gas line to the appliance location or, of course, gas appliance costs.
Gas Line Advice and Installation Quotes from Plumbers Near You

Gas Line Advice and Installation Quotes from Plumbers Near You

Retail Gas Line Cost – Pipe and Supplies

Even if you DIY, you’ll need the gas shutoff valve and might need to buy a tool or too.

  • $10 – $40 | Gas Appliance Shutoff Valve
  • $100 – $300 | Main Shutoff Valve – Price depends on the size of pipe that is connected to the natural gas meter.
  • $12 – $40 | 12-inch Adjustable Wrench
  • $15 – $50 | Gas Pipe Cutter
  • $3 – $6 per Roll | Teflon Pipe Tape
Gas Line Advice and Installation Quotes from Plumbers Near You

Gas Line Advice and Installation Quotes from Plumbers Near You

Permits, Inspection, Related Costs and Installation Time

Permits and Inspection Cost

  • $0 – $75 | Whether or not a permit is required is determined by the state in which the shut off valve is being installed.  Most states do not require a permit to install or replace a gas shut-off valve at an appliance location.  Always check local codes before doing this job or anything related to gas work.

Related Costs

Here are a few itemized costs related to installing a gas line shutoff valve. You might have a few of these depending on the scope of your project, and their cost are in addition to what prices for gas line installation.

  • Cost to Remove Gas Line: $6.00 – $8.00 per foot
  • Cost to Convert an Appliance for Propane: $40 – $75
  • Cost to Hook Up a Gas Appliance: $45 – $60 per appliance
  • Cost to Run Gas Line from Street to House (includes trenching, gas line installation and connections, backfilling): $700 to $1,250 for most suburban lots – more for homes set far off the road
  • Cost to Install a Free Standing Fireplace: $1,485 – $2,775
  • Cost of a Gas Line Pressure Test: $75 – $150, according to HomeGuide, and that’s a pretty accurate estimate
  • Cost to Install a Vent Flue: $650 – $950, required for many gas-burner appliances

Other Costs and Installation Time

Plumbers or heating and cooling specialists will generally charge between $100-$300 for labor. Angie’s List suggests $200 to $350 in plumber costs; Home Advisor puts plumbing labor at about $150 to $200 plus the cost of installation supplies. See the cost factors above to narrow the range that you’re likely to pay when hiring a pro for the job.

This is a pretty straightforward, quick job, especially when the location is easy to access.

  • Up to 1 Hour | Gas Shutoff Valve Installation

DIY or Hire a Pro?

steve-hansen

A gas shut-off valve should be installed by a licensed plumber or heating/cooling contractor.  Code and regulations need to be followed carefully.  For example, all shut-off valves for gas appliances, such as gas stove/oven, gas dryers, and gas fireplaces must be installed within six feet of the appliance.

In our opinion, whenever gas is involved, it makes sense to hire a licensed plumber or heating/cooling contractor. They’ll install the proper valve type for the purpose it is used, ensure a secure fit and check for leaks. This is of those “safety first” home projects best left to a pro.

What do you think?

Gas Line Advice and Installation Quotes from Plumbers Near You

Gas Line Advice and Installation Quotes from Plumbers Near You

Is This a DIY Project? What do You Think?

You already voted!

Costs Submitted by Homeowners and Pro’s

    Share Your Project Cost for Others to Compare

    Share Your Project Cost for Others to Compare

    (Provide a Brief Title About Your Project, Repair, Remodel, etc)
    (Used so others in your area can compare)
    (Required for Pros)
    In order to help us and others understand the detailed nature of your project, please include as many details as possible. For instance, if you had a pool installed, tell us the size. If you had a fence, share how many gates, the height, etc. Details are the most important part of this.
    Sending