The average cost to install a new circuit breaker is $187. The cost is as low as $130 for 15 amp to 30 amp breakers and as high as $280 for breakers up to 200 amps or when the circuit breaker is an older one with limited availability. You can Do it yourself for under $30 if you have an electrical license, but it’s not suggested otherwise.
How Much does it Cost to Install a Circuit Breaker?
$130 – $155
Average Cost Estimate
$160 – $200
$215 – $280
|Circuit Breaker Cost||$5 – $20||$22 – $45||$50 – $150|
|Poles||1 pole||1 or 2 poles||Mostly 2 poles|
|AFCI/GFCI||No||Mostly No||Yes or No|
|Amps: Non-GFCI||15 – 30||30 – 100||100 – 225|
|Labor Rates||Low to Average||Average||Average to High|
|Number Installed||2 or More||1 or More||1 or More|
|Part Availability||Common||Common||Common or Not Common|
|Job Complexity||Easy||Easy to Moderate||Easy to Difficult|
Overview of Circuit Breaker Installation in Electrical Panel
Circuit breakers wear out with time or can be damaged by an electrical short. Before replacing the breaker, make sure it isn’t just tripped. Turn it to the ‘off’ position and back to the ‘on’ position. If the plugs or switches on the circuit still aren’t energized, then circuit breaker replacement is probably necessary.
This page gives the details that will allow you to closely estimate your circuit breaker replacement cost. These include cost factors, cost of the part vs labor cost, prices paid by other readers to have this work done and costs from estimating sites.
We invite you to share your circuit breaker repair price too.
Product Cost Details
Circuit Breaker Replacement Price Factors
This is a straightforward repair, but there are a few factors that affect price.
- Labor Rates in Your Area – Most breakers cost less than $25, so the major expense is labor. On the Coasts and in major metro areas, the cost of living is higher. Labor rates can be as much as $150 per hour, sometimes higher. In rural areas and small towns in the Midwest and South, labor rates start below $90/hour for licensed electricians.
- Who Does the Work – Electricians start as Apprentices, then become Journeymen with the top rank being Master Electrician. The labor cost goes up with each level achieved.
- Circuit Breaker Specs – Most breakers are 1-pole/120V units from 15 to 50 amps, and they are not expensive. Prices for 2-pole/240V 100 amp to 225 amp breakers are two to five times higher. Price details are listed below.
- AFCI/GFCI – Arc fault circuit interrupter and ground fault circuit interrupter breakers cost two to three times more than standard 15 and 20 amp breakers cost. These breakers are used in kitchens and bathrooms where shock from electricity and water interaction is possible.
- How Many Breakers are Replaced – Cost per breaker replaced goes down slightly as the number of breakers switched out goes up. This is because electricians have minimum service fees in excess of $75 that covers their travel time and expense to come to your house. The more breakers the fee is spread over, the lower the average cost per breaker.
- Part Availability – If the part is a common one and still manufactured, cost is low. When the part is older and hard to get, cost can double or triple. See parts costs below.
- Job Complexity – If access to the electrical panel is difficult, job cost will go up slightly. This is not a factor in most jobs.
Cost of Installation Supplies
Circuit breaker cost depends on the factors shown. Here are average ranges for the most common circuit breakers used.
- $5 – $30 | 1-pole, standard 15 amp to 30 amp circuit breakers
- $10 – $40 | 1-pole, standard 50 amp to 100 amp circuit breakers
- $40 – $60 | AFCI/GFCI circuit breakers
- $9 – $45 | 2-pole, standard 15 amp to 30 amp circuit breakers
- $28 – $150 | 2-pole, standard 50 amp to 200 amp circuit breakers
The majority of circuit breakers are 15, 20 or 30 amps.
Permits, Inspection, and Unit Installation Costs
- $0 | In most areas, a permit is not required to replace circuit breakers. You will need a permit if wiring is installed, fuses are being replaced with circuit breakers or the entire electrical panel is being replaced.
Installation Labor Cost
Electrician labor rates range from about $75 to $200 per hour. Labor cost factors are discussed in the price factors above. They include the certification level of the electrician and where you live.
Replacing a circuit breaker is a quick repair.
- 45 minutes – 1 hour | Removing the panel cover, replacing one breaker and replacing the cover
- 20-40 minutes | Replacing each additional circuit breaker
DIY or Hire a Pro
Doing your own electrical work is something we don’t recommend due to the risk of mild shock to fatal electrocution.
To do the job safely requires basic knowledge of electricity, panels, circuit breakers and how to shut off the power and make sure it is off with an electrical tester. Then the replacement must be done properly.
Having said that, many homeowners take the risk and safely make this repair. There are good tutorials like this 5-minute video available.
Circuit Breaker Installation Costs from Around the Web
|Costimates||$187||$130 – $280|
|Porch||$234||$213 – $254|
|Home Advisor||$140||$105 – $170|
|HomeWyse||$231||$188 – $273|
|Thumb Tack||$160||$120 – $200|
|Suggest a Cost Comparison from Another Website|